Before you ride

Everything you need to assemble, fold, configure, and operate your JOFEN T10 before the first ride.

Unboxing & Assembly

See what is included and follow the essential assembly steps to get your T10 ready for setup.

Reading more

Accessories included

  • User manual
  • Spare inner tube
  • Spare screws
  • Installation tools
  • Charger

Folding & Unfolding

Use the safety pin and folding handle in the correct order to fold or unfold the stem securely.

Reading more

How to fold the T10

  1. Turn off the scooter and keep it on a stable, level surface.
  2. Pull the red safety pin out from the side of the folding mechanism.
  3. Pull open the folding handle at the bottom of the stem.
  4. Carefully lower the stem into the folded position.

How to unfold the T10

  1. Pull open the folding handle.
  2. Push the stem forward into the upright riding position.
  3. Close and secure the folding mechanism.
  4. Insert the red safety pin again.
  5. Check that the stem is fully locked before riding.

The supplied video shows a close-up of the safety pin and locking mechanism. It does not show a complete fold-and-unfold cycle.

Display & Control

The central display gives you quick access to essential ride information and current operating status.

Video

Reading more

Use the display to check your current settings before every ride. Make sure the selected drive mode and other indicators match the way you intend to ride.

Button Functions

Power the scooter, switch the drive system, and adjust display settings using the handlebar controls.

Reading more

Long-press the Power button to turn the scooter on or off.

Press the M button once to switch between single-motor and dual-motor drive. Long-press the M button to enter the P-setting menu.

In the P-setting menu, use the + and − buttons to select a P-code or adjust its value. Press the M button once to confirm the selected value, then long-press the M button to save your changes and exit.

Display Settings & P-Codes

Customize key display and riding settings through the P-setting menu.

Reading more

How to Change a Setting

Long-press the M button to enter the P-setting menu. Use the + or − button to select the required P-code, then press M once to open or confirm the setting. Adjust the value with the + or − button, press M once to confirm the new value, and finally long-press M to save your changes and exit the menu.

P-Code Reference

P02 – Units: Select 0 for km/h or 1 for mph. The default setting is 0.

P04 – Auto Sleep: Select 0 to turn automatic sleep off, or choose a value from 1 to 60 minutes. The default setting is 10 minutes.

P06 – Wheel Size: Sets the wheel diameter in inches. The default value is 10.0.

P07 – Motor Magnets: Adjusts the motor-magnet value from 1 to 100. The default value is 30.

P09 – Start Mode: Select 0 for zero-start operation or 1 for kick-start operation. The default setting is 1.

P10 – Speed Limit: Set the value to 0 to remove the electronic speed limit.

P12 – Start Torque: Adjusts the starting torque from 0, the weakest setting, to 5, the strongest setting. The default value is 5.

P15 – Motor Power: Adjusts motor output up to 100%. The default value is 100.

P16 – Cruise Control: Select 0 to turn cruise control off or 1 to turn it on. The default setting is 0.

P99 – Factory Reset: Restores the factory settings. Use this option only when necessary.

Recommended Setup

For the recommended setup, set P09 Start Mode to 0 to enable zero-start operation, and set P10 Speed Limit to 0 to remove the electronic speed limit.

Safety notice: Zero-start operation and unrestricted speed can increase the risk of sudden acceleration, loss of control, injury, or property damage. Only use these settings where permitted by local laws, wear appropriate protective equipment, and test the scooter in a controlled area first.

Single & Dual-Motor Drive

Choose efficient single-motor drive or stronger dual-motor performance to suit the route and riding conditions.

Reading more

Press M once to switch between single-motor and dual-motor drive. Confirm the selected drive system on the display before accelerating.

Use single-motor drive for smoother power delivery and everyday riding. Select dual-motor drive when additional traction or acceleration is needed. Accelerate progressively, especially on loose, wet, or uneven surfaces.

Lighting & Turn Signals

Use the scooter's lighting and indicators to improve visibility and communicate your direction to other road users.

Reading more

Check the lights and turn signals before every ride. Do not rely on lighting alone—ride defensively and follow local traffic rules.

FAQ

How do I turn the JOFEN T10 on or off?

Long-press the Power button to turn the scooter on or off.

How do I switch between single-motor and dual-motor drive?

Press M once. Check the display to confirm the selected drive system before accelerating.

How do I enter the P-setting menu?

Long-press M. Use + and − to select a code or change a value, press M once to confirm, and long-press M to save and exit.

What are the recommended P09 and P10 settings?

The recommended setup is P09 = 0 for zero-start operation and P10 = 0 to remove the electronic speed limit. Only use these settings where legal and safe.

How do I fold the scooter?

Turn off the scooter, pull out the red safety pin, open the folding handle at the bottom of the stem, and carefully lower the stem.

How do I unfold and secure the scooter?

Open the folding handle, push the stem forward into the riding position, secure the mechanism, and insert the red safety pin again. Check that the stem is fully locked before riding.

What should I check before riding?

Confirm that the folding mechanism and red safety pin are secure, the display and controls operate correctly, the selected drive mode is appropriate, and the lights and turn signals work normally.

Need more Help? Contact Us